Looks like you access from European region.
Would you shop at webike.eu.com?
976.51 HKD (19,890 日幣)
配送訊息
If manufacturer have in stock, ships around 17th Jun. 2026
商品詳情
[Material]Steel
Contents]BodyX1
[Size]
Width:Approximately 700mm
Height 1 (when Grip portion is horizontal):Round Straight
Pull 1 (Grip portion horizontal):Approximately 182mm
Height 2 (Start up Vertical):3000K (Yellow)/6000K (White)
Opening 2 (When Launched Vertical):Approximately 183mm
Clamp width:Approximately 120mm
Handlebar diameter:Clamp part Φ25.4mm/Grip part Φ22.2mm
**Depending on the individual variability, the banjo may be oriented too far outward and tension may be applied to the brake hose. In this case, loosen the banjo bolt slightly and change the direction.
*If you loosen it too much, fluid may leak or air may be sucked out.
*If the brake hose is turned inward too far, the brake hose will interfere with the tank.
*You need to adjust the angle of installation for inspection.
*We have omitted descriptions of the tools to be used and general wiring procedures.
*If you are unsure about the installation, please contact a knowledgeable person or a custom store.
*Some adjustments may be necessary depending on the individual differences of the car body.
*There are cases that it contains other product in the photo.
*Please note that the product specification may change due to manufacturer reasons.
.
Comfort Bar" Series for RH975NIGHTSTER
Comfort the ride.
GLEAMING WORKS "Comfort Bar" Series, which focuses on position thoroughly, is now available for RH975NIGHTSTER..
ABOUT COMFORT BAR
The COMFORT BAR was designed with the theme of a handle position that matches the Japanese body shape, based on the developer's actual riding experience and Harley user feedback..
The position of the arms is comfortable and comfortable, making it ideal for long tours.. (Approx. 108mmBack compared to OEM)
Easy installation & comfort
No need to replace hose and cable.
The handle position is 108 back from the OEM, and a comfortable riding position can be realized..
Details.
Finished with Cation electrodeposition coating with excellent rust-preventive properties + DoubleCoat with a top coat of powder coat.
Slot for positioning Switch box.
NORMAL bar end mirrors can also be installed..
[Comfort Bar replacement procedure]
If the Meter is on the Riser, remove it and the Wiring..
Please cover the tank with a cover to prevent scratches..
Remove the Mirror and Adapter from the Bar End section with Quantity:Pair (for Left and Right)..
Disconnect the coupler connected to the ClutchBracket.. It is easy to pull it out by lightly pulling it while pressing the lock part..
Remove the TorqueQuantity:2pc and remove the ClutchBracket..
Remove the Left Side Grip.. Torque can be found by slightly turning up the rubber on the inside of the Switch Box..
Remove this part to remove the grips.. Torque here is easy to lick, so loosen with care!.
Remove TorqueQuantity:2pc from the back of the switch box and remove the cover from the back of the switch box.. Please be careful not to break the smallest nail on the inside..
Remove Coupler. Wiring on the Clutch Side is now free..
Loosen the bolt securing the switch box and remove the switch box from the handlebar.. This completes the removal of the Clutch Side..
The other side is removed in the same manner..
After all parts have been removed, remove the bolt from the Clamp section and remove the Handlebar..
Install the handlebar in the reverse order of the removal procedure..
Check the angle, Quantity:Pair (for Left and Right), etc., and then temporarily fix the handlebar.. Adjustment of the angle, etc., while installing the Switch box is recommended..
Once everything is in place, tighten the bolts to secure it in place.. At this time, as even as possible etc.. Make sure to tighten alternately so that Bolt tightens to.
In the switch box of Quantity:Pair (for Left and Right), there is a Knob for positioning..
The Comfort Bar here has a slot for OEMs in Quantity:Pair (for Left and Right), so please place the switch box so that the Knob fits into the slot.. If you adjust the angle in the slot, it will be easier to align the Quantity:Pair (for Left and Right)..
After installing the Brake master, check the orientation of the banjo..
Tension on the brake hose may be too far outward.. In this case, loosen the banjo bolt slightly and change the orientation.. If loosened too much, the Fluid may leak or bite the air, so change the direction carefully and fix it firmly.. Note that if the hose is pointed too far inward, the brake hose will interfere with the tank..
[Confirmation]
After all installation is complete, check the following.
Before getting on the car, check that the wires and hose are installed without any difficulty..
I tried to turn off Handlebar and found it to be uncomfortable.. is there any other way to.
Are switches and other equipment working properly?.
After riding, loosening etc.. is there any other way to.
警告
* 如果商品有附上說明書,說明內容有可能是日文的。